Tikka T3x Length of Pull Kit — LOP Spacers for T3 / T3x / T1x
// Fitment & specsDetails before you buy
Key details on fit, setup and use before you buy.
Three simple steps
Remove the recoil pad
Back out the two pad screws and lift the pad from the stock.
Choose one spacer
Fit the locating adapter plate with either the 10 mm or 20 mm spacer as the default setup.
Special-case stack
If 30 mm is genuinely required, glue the spacer pieces together and contact us first to confirm the locating and fastening hardware.
Reattach and check
Use the included longer screws. Stop and contact us if the pad does not align or tighten securely.
Common questions
What if my stock already feels too long?+
If the stock already feels too long after eye relief is set, do not add LOP spacers yet. Send fit notes first.
Can I stack both spacers for 30 mm?+
For every LOP spacer, use one spacer by default. Stacking any combination of LOP spacers can be done only in special cases, but a multi-piece stack does not create the strongest possible connection and is not our recommended default. If stacking is required, glue the spacer pieces together before final installation and use only the confirmed locating and fastening hardware for the setup. Contact us first if the stacked setup and hardware have not already been confirmed.
Are longer screws included?+
Yes. The standard kit includes longer recoil-pad screws for the supplied 10 mm or 20 mm setup. Contact us first for a 30 mm stack or a non-standard recoil pad.
How much length of pull can I add as supplied?+
Choose either the 10 mm spacer or 20 mm spacer as the default setup. For every LOP spacer, use one spacer by default. Stacking any combination of LOP spacers can be done only in special cases, but a multi-piece stack does not create the strongest possible connection and is not our recommended default. If stacking is required, glue the spacer pieces together before final installation and use only the confirmed locating and fastening hardware for the setup. Contact us first if the stacked setup and hardware have not already been confirmed.
Will it fit my Tikka and recoil pad?+
It is designed for Tikka T3, T3x, and T1x factory stocks. If you use an aftermarket stock or recoil pad, send a clear photo before ordering so we can check the fit path.
Is it a permanent modification?+
No. It installs between the stock and recoil pad without drilling or permanent stock modification.
Do I need a gunsmith?+
No. A normal 10 mm or 20 mm setup uses the two recoil-pad mounting points and the included longer screws. Stop and contact us if the pad does not align or tighten securely.
What is length of pull and why does it matter?+
Length of pull is the distance from the trigger to the back of the recoil pad. Set eye relief first, then choose only the extra length your position needs.
Do you ship internationally?+
Yes. Available shipping options and any duties or taxes are shown in cart and checkout before payment.
Full details, specs & FAQ
Length of pull (LOP) is one of the most overlooked variables in Tikka rifle fit. Too long and you reach for the trigger. Too short and you feel cramped behind the scope. Set eye relief first, then measure the extra length you actually need.
The Nokka LOP Spacer Kit is designed for Tikka T3, T3x, and T1x factory stocks. The standard kit includes one locating adapter plate, a 10 mm spacer, a 20 mm spacer, and longer recoil-pad screws. As supplied, choose either the 10 mm or 20 mm spacer for one rifle.
Stacking rule for every LOP spacer: For every LOP spacer, use one spacer by default. Stacking any combination of LOP spacers can be done only in special cases, but a multi-piece stack does not create the strongest possible connection and is not our recommended default. If stacking is required, glue the spacer pieces together before final installation and use only the confirmed locating and fastening hardware for the setup. Contact us first if the stacked setup and hardware have not already been confirmed.
Not sure how much you need? Use the Tikka fit checklist or read the length-of-pull fitting guide before ordering.
What's in the standard kit
- 1× Locating adapter plate
- 1× 10 mm spacer (0.4″)
- 1× 20 mm spacer (0.8″)
- 2× Longer recoil-pad screws for the supplied 10 mm or 20 mm setup
Compatibility
Designed for Tikka T3, T3x, and T1x factory stocks. Recoil pads and aftermarket stocks can vary; if your rifle does not have the factory stock and pad, send us a photo before ordering and we will check the fit path.
Specifications
- Supplied adjustment: 10 mm or 20 mm
- 30 mm setup: contact us first to confirm the required locating hardware
- Weight: approximately 100 g for the standard kit
- Made in Australia
If you also need cheek-height adjustment, compare the Tikka Performance Kit before buying the two fit products separately.
Common questions
How much length of pull can the standard kit add?
Use the supplied 10 mm spacer or 20 mm spacer. Contact us before planning a 30 mm stack so we can confirm the correct locating hardware for your exact setup.
Are longer screws included?
Yes. The standard kit includes longer recoil-pad screws for the supplied 10 mm or 20 mm setup. If you are planning a 30 mm stack or using a non-standard recoil pad, contact us first so we can check the required hardware.
Will it fit my stock and recoil pad?
It is designed for Tikka T3, T3x, and T1x factory stocks. If you use an aftermarket stock or recoil pad, send us a clear photo of the pad and stock before ordering.
Is it a permanent modification?
No. It installs between the stock and recoil pad without drilling or permanent stock modification.
Do I need a gunsmith?
No. A normal 10 mm or 20 mm setup uses the two recoil-pad mounting points and the included longer screws. Stop and contact us if the pad does not align or tighten securely.
Do you ship internationally?
Yes. Available shipping options and any duties or taxes are shown in cart and checkout before payment.
Complete the setup
